Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
The writer is making a few great points regarding How to Install a Bathtub as a whole in the content in the next paragraphs.
Mounting a bath tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably hard job. If the old tub is readily accessible, the task can move rapidly; if you need to open a wall surface to remove the old bathtub and position the brand-new tub, the job is much harder. In either situation, the job is within a home handyman's abilities, although you will certainly require an assistant to move out the old tub and also set in the brand-new one. See to it you have certified yourself for the task and are comfortable trying it. As opposed to employing a contractor to take over a halfway-completed task, it is better to think about using one prior to you start. Opportunities are you might need an expert plumber to make tube links.
This article will assist you mount a brand-new bathtub in your restroom if you have actually currently acquired a brand-new bathtub and don't need to change the plan of your previous water system pipes.
Your tools as well as material checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite problematic as a result of the restricted accessibility that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Before proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area in between the faucet and the sink. Safeguard the faucet in position with the maker given backnut. When the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind needs to be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the called for placement. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bathtub up until the spirit level reads degree.
To mount faucets, fit the bottom of the outermost versatile faucet adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water supply as well as check all joints and also new pipework for leaks and also tighten them if necessary. Fill up the tub and also check the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and securing around the bath tub must wait until the bathtub has actually been utilized at least when as this will resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining frame supplied with the bathroom should be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid strain on the bath tub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, resulting in problems with wetness and also possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components as well as fittings. They are offered in tubes and also cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can break fairly very early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our topic about Tools You Need to Install a New Bathtub . Many thanks for taking time to read our short article. Sharing is good. Helping people is fun. Thanks a lot for going through it.
Schedule Now! Report this page